HF 540CM TILTING FLOW CHANNEL, 400 mm wide

HF 540CM TILTING FLOW CHANNEL, 400 mm wide

Enquiry

Download

The channel is designed for studying the hydraulic flow phenomena. It is a service unit to be used with optional accessories and models below. Instruction manual is also included.

Under Frame
The channel bed rests on twin beams under frame which ensures static loading deflections are kept to a minimum. Each section is shipped with glass side walls. This simplifies site installation and is easier to ensure alignment of the channel. The beams are supported by a fulcrum at one end and an adjustable height support at the other end.

Slope Adjustment
The adjustable height support uses twin screws. Each screw is driven by a worm and wheel gear box with a common motor. A slope scale is provided at one end of the flume.

Channel Bed
The channel bed is made of stainless steel with screw holes of equal distance along the channel length to hold accessories or models to the channel bed. These holes can also be used for pressure tapping to measure pressure loss along the channel length (optional).

Side Walls
For safety reasons, the side walls are made of tempered glass or clear acrylic. The walls are supported at interval by brackets with screw adjustment to ensure that the channel wall is straight and vertical.

Head Tank
The head tank is made of stainless steel and its sides and bottom are curved to ensure smooth flow into the channel. Perforated sheets are also provided in the head tank to further smoothen the flow.

Storage Tank
The storage tank has adequate water to fill the full channel. Fiber glass storage tank(s) is provided at downstream end of the channel. Capacity of tank varies according to channel length.

Circulating Pump
The pump seal is mechanical. A geared butterfly valves is provided for accurate flow control.

Flow measurement
A flow digital display is used for easy observation on flow adjustment. A water meter is available as an option and may be used as a reference for flow indicator setting later.

Safety Device
Limit switches for slope, level switches for water level, emergency stop, and ELCB.

Model and Accessories ( Optional)
All accessories and models have side seals to ensure no water seepage or leakage through the sides of the models. A wide variety of models and accessories are available as an option.

. Flow measurement
. Hydraulic jump
. Analysis of model structures
. Gauging structures
. Velocity profile
. Continuity and energy equations
. Similarity laws
. Roughened bed characteristics
. Surge propagation
. Sediment transport study system
. Wave generation and absorption

  • Channel size
: 400 mm wide, 500 mm high   
  • Channel length
: 12.5 m working section. Other length, i.e. 5, 7.5, 10 m, or can be supplied on request (optional).   
  • Tilting adjustment
:  -1% to +3%   
  • Side walls
:  6 mm tempered glass   
  • Channel bed
:  Stainless steel   
  • Water storage tank
:  Fiber glass over 1500 L   
  • Head tank
:  Stainless steel    
  • Sluice gate
:  Stainless steel, rack and pinion type, built-in at downstream end of channel   
  • Pump
:  5.5 kW with a maximum flow rate approximately 1800 Lpm   
  • Flow measurement
:  Flow digital display   
  • Power supply

:  380 V, 3 Ph, 50 Hz. Other power supply is available on request.

   
     
  • Shipping Dimensions: One 40 ft. container (without storage tank)
  • Mobile ladder with brake wheels and guardrail for model installation.
  • HF540-001
Instrument carriage, manual operated.
  • HF540-001A
Motorized instrument carriage instead of manually operated.
  • HF540-085
End tank, stainless steel, at downstream end of flume
  • HF540-090
Checker plate walkway along one side of the flume
  • HF540S

Learning Software

 to support both online/offline training with data calculation and analysis by manual data entry from standard measuring instruments
  • HF540-019
Stainless steel vernier hook and point gauge 450 mm with 0.05 mm reading.
  • HF540-019A
Stainless steel hook and point gauge 450 mm with plastic vernier scale 0.5 mm reading.
  • HF540BWB
Basic weir base
  • HF540-020
Stainless steel 60˚V notch or 90˚V notch
  • HF540-021
Rectangular notch weir
  • HF540-022
Sharp crested weir with weir base.
  • HF540-023
Broad crested weir, sharp edges
  • HF540-023A
Round edge attachment for HF530-023
  • HF540-024
Crump weir
  • HF540-025
Trapezoidal weir
  • HF540-030
Ogee weir consisting of base profile unit with both upstream and downstream pressure tappings and manometer board
  • HF540-031

Dam spillway consisting of base profile unit with different interchangeable downstream sections:

 - Toe, ski jump, piers and pegs, gravel box, stop logs, chute block, baffle block with five rectangular blocks, baffle block with five triangular blocks, and end sill with different height.
  • HF540-032
USBR type 2,3 or 4 energy dissipater.
  • HF540-033
Syphon spillway made from clear acrylic and PVC
  • HF540-034
Bridge pier, round or square edge
  • HF540-035
Culvert fittings, round or square , horizontal or drop inlet with or without entrance flare Tube is made from clear acrylic
  • HF540-036
Vibration pile
  • HF540-040
Venturi flume made from clear acrylic.
  • HF540-041
Parshall flume made from clear acrylic.
  • HF540-042
Submerged orifice made from stainless steel on plastics.
  • HF540-043
Trapezoidal flume made from clear acrylic.
  • HF540-050
Sluice gate, rack and pinion drive with stainless steel attachment
  • HF540-052
Radial gate, rack and pinion drive with stainless steel attachment
  • HF540-060
Pitot tube with manometer board for measurement of flow velocity and various channel sections
  • HF540-061
Current meter: digital or analog indicator, low speed probe from 5 to 150 cm/s or high speed probe 60-300 cm/s
  • HF540-065
Lift and drag balance and models, large and small cylinders and aerofoil section
  • HF540-070
Roughened bed, gravel, sand, or corrugated , 2.4 m
  • HF540-071
False floor section (Sill).
  • HF540-075
Sediment transport study system
  • HF540-080
Wave generator with  variable speed geared motor, maximum stroke 20 cm
  • HF540-082
Absorbing beach, plain, roughened, or permeable.
  • HF540-085
End tank, stainless steel, at downstream end of flume.
  • HF540-090
Checker plate walkway along one side of the flume.
  • PH100-020
Multi tubes water manometer, 10 tubes, water pressure 450 mm.
  • Rake model.
 
  • HF540-150
Computer Interface
 This includes computer interface and software for data display of flow rate and slope by computer.
  • HF540-160
Computer Control
                                This includes pump speed, tilting, display of pressure distribution and computer interface unit for key data acquisition and software for control by computer.
  • Other accessories and models can be supplied on request.
  • HF540S                        
: Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
SIMILAR PRODUCTS

HF 566 SEDIMENT FLOW CHANNEL, 600 mm Wide

HF 566 SEDIMENT FLOW CHANNEL, 600 mm Wide

Enquiry

Video

Download

The channel is designed for studying the sediment transport and bed forms as well as flow phenomena without sediment. It is a service unit to be used with optional accessories and models. Instruction manual is also included.

Under Frame

The channel bed rests on twin I-beam under frame which ensures static loading deflections are kept to a minimum. The length of the I-beam is about 6 m Each section is shipped with glass side walls. This simplifies site installation as there are less joints and is easier to ensure straight side walls throughout the length. To ensure minimum deflection, the I beam base frame of 18 m is supported by a fulcrum at the middle and adjustable height support at both upstream and downstream ends for a total of 3 supports.

Slope Adjustment

Each adjustable height support uses twin screws and with a system of worm and wheel gear boxes and miter gears which are intern driven by a motor. A slope scale is provided at one end of the flume.

Channel Bed

The channel bed is made of stainless steel with twin screw holes of equal distance along the channel length to hold accessories or models to the flume bed when used as a normal tilting flow channel. These holes can also be used for pressure tapping points to measure pressure loss along the channel length.

Side Walls

For safety reasons, the side walls are made of tempered glass. The walls are supported at interval by brackets with screws for vertical position adjustment.

Instrument Carriage

Top rails made of stainless steel tubes are attached to the top angle on each wall of the channel. Screws supporting the rails can be adjusted to ensure uniform height and in a straight line. A scale graduated in mm. is attached along the full length of one top angle of the walls. The instrument carriage is manually operated.

Head Tank

The head tank is made of stainless steel and its sides and bottom are curved to ensure smooth flow into the channel. Perforated plates are also provided in the head tank to further smoothen the flow.

Sediment Feeder

The channel bed may be filled by a sediment feeder with a slope stopper upstream and another one just before sediment trap at the downstream end of the channel. Feeding is by a screw.

Sediment Trap

A Sediment trap is provided at the downstream end of the channel. The trapped sediment can be discharged by

 a bottom value. The trap is covered when used as a normal flow channel.

Storage Tank

An underground concrete storage tank is recommended as standard. This tank is to be built by the user. However, above ground tank is available (optional).

Walkway

A steel walkway with a checker plate floor and side rails is provided on both side of the flume for ease of model installation and flow observations.

Circulating Pump

The pump is ceramic coated to minimize wear by sediment abrasion. A mechanical seal is used. A geared butterfly valve is provided to control accurate rate of flow.

Flow measurement

A flow digital display is used. In the case of an underground storage tank, a measuring tank with a calibrated weir is available as an option. The flow rate is controlled by a geared butterfly valve.

Model and Accessories

In the case of no sediment, the channel may be used as a normal tilting flow channel. All accessories and models have side seals to ensure no water seep or leak through the sides of the models. A wide variety of models and accessories are available as an option.

As Sediment Channel:  

  • Fixed smooth bed flow
  • Flow over mobile sand bed
  • Flow structures
  • Local scour
  • Mechanics of sediment transport
  • Bed form hysteresis
  • Depositionary features and fancies
  • Computational work
  • Flow over fixed gravel bed

 

As Tilting Flow Channel:

  • Flow measurement
  • Hydraulic jump
  • Analysis of model structures
  • Gauging structures
  • Velocity profile
  • Continuity and energy equations
  • Similarity laws
  • Roughened bed characteristics
  • Surge propagation
  • Channel size
: 600 mm wide, 700 mm high   
  • Channel length
: 18 m (12 m length can be supplied on request)   
  • Total length
:  Additional length 3 m for head and storage tanks.   
  • Tilting adjustment
: -0.5 to +2%   
  • Side walls
: Tempered glass   
  • Channel bed
:  Stainless steel   
  • Sediment feeder     
:  Motorized   
  • Sediment trap         

:  Stainless steel with cover and sediment recovery system

   
  • Water storage tank

:  Underground tank to be provided by user. Aboveground tank is optional

   
  • Head tank
:  Stainless steel   
  • Sluice gate
:  Stainless steel, rack and pinion type, built-in at downstream end of flume   
  • Pump      
:  1   
  • Flow measurement
:  Flow digital display   
  • Instrument trolley
:  Manual operated   
  • Power supply
:  380 V, 3 Ph, 50 Hz. Other power supply is available on request.   
  • Shipping Dimensions: One 40 ft. container (without storage tank)
  • HF566S                               

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HF560-001A
Motorized instrument trolley instead of manual operated trolley
  • HF560-002
Above ground storage tank, fiber glass or stainless steel, with lids

As A Sediment Flow Channel:

  • HF566-010                
Sediment drying oven.                                                                                                                              

As A Tilting Flow Channel:

  • HF566-017
Flow calibration tank
  • HF566-019
Stainless steel vernier hook and point gauge with vertical and horizontal movement
  • HF566-020
Basic weir plate with stainless steel 60˚ V notch and rectangular notch weir attachment.
  • HF566-022
Sharp crested weir
  • HF566-023
Broad crested weir, sharp edges
  • HF566-023A
Round edge attachment for HF560-023
  • HF566-024
Crump weir
  • HF566-025
Trapezoidal weir
  • HF566-030                      
Ogee weir with consisting of base profile unit both upstream and downstream pressure tappings and manometer board
  • HF566-031
Dam spillway consisting of base profile unit with different interchangeable downstream sections:
 - Toe, ski jump, piers and pegs, gravel box, or stop logs
  • HF566-032
USBR type 2,3 or 4 energy dissipater
  • HF566-033
Syphon spillway
  • HF566-034
Bridge pier, round or square edge
  • HF566-035
Culvert fittings, round or square, horizontal or drop inlet with or without entrance flare
  • HF566-036
Vibration pile
  • HF566-040
Venturi flume
  • HF566-041
Parshall flume
  • HF566-042
Submerged orifice made from stainless steel on plastics
  • HF566-050
Sluice gate, rack and pinion drive with stainless steel attachment
  • HF566-052
Radial gate, rack and pinion drive with stainless steel attachment
  • HF566-060
Pitot tube with manometer board for measurement of flow velocity and various channel sections
  • HF566-061
Current meter
  • HF566-065
Lift and drag balance and models, large and small cylinders and aerofoil section
  • HF566-070
Roughened bed, gravel, sand, or corrugated
  • HF566-075R
Sediment transport study system with sediment recirculating system

 

In this case, pump will be cover with ceramic for corrosion prevention.
  • HF566-080
Wave generator with variable speed geared motor
  • HF566-080F
Full randomly wave generator

 

This include HF560-082 and HF560-080M.
  • HF566-080M
Wave measuring system
  • HF566-082
Absorbing beach, plain, roughened, or permeable
  • HF566-085
End tank, stainless steel, at downstream end of flume
  • Other accessories and models can be supplied on request.
  • Other optional equipment, please contact manufacturer ([email protected])
  • HF566S                        
: Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
SIMILAR PRODUCTS

HF 560 TILTING FLOW CHANNEL, 600 mm wide

HF 560 TILTING FLOW CHANNEL, 600 mm wide

Enquiry

Video

Download

The channel is designed for studying the hydraulic flow phenomena. It is a service unit to be used with optional accessories and models. Instruction manual is also included.

 

Under Frame

The channel bed rests on twin I-beam under frame which ensures static loading deflections are kept to a minimum. The length of the I-beam is about 6 m. Each section is shipped with glass side walls. This simplifies site installation as there are only two joints and is easier to ensure straight side walls throughout the length. To ensure minimum deflection, the I beam base frame of 18 m. is supported by a fulcrum at the middle and adjustable height supports of both upstream and downstream ends for a total of 3 supports.

 

Slope Adjustment

Each adjustable height support uses twin screws and with a system of worm and wheel gear boxes and miter gears which are intern driven by a motor. A slope scale is provided at one end of the flume.

 

Channel Bed

The channel bed is made of stainless steel with twin screw holes of equal distance along the channel length to hold accessories or models to the flume bed. These holes can also be used for pressure tapping to measure pressure loss along the channel length.

 

Side Walls

For safety reasons, the side walls are made of tempered glass or clear acrylic. The walls are supported at interval by brackets with screws for vertical position adjustment.

 

Instrument Carriage

Top rails made of stainless steel tubes are attached to the top angle on each wall of the channel. Screws supporting the rails can be adjusted to ensure uniform height and in a straight line. A scale graduated in mm. is attached along the full length of one top angle of the walls. The instrument carriage is manually operated.

 

Head Tank

The head tank is made of stainless steel and its sides and bottom are curved to ensure smooth flow into the channel. Perforated plates are provided in the head tank to further smoothen the flow.

 

Storage Tank

An underground concrete storage tank is recommended as standard. This tank is to be built by the user. However, above ground storage tank is available (optional).

 

Walkway

A steel walkway with a checker plate floor and side rail is provided on one side of the flume for ease of model installation and flow observations.

 

Circulating Pump

The pump seal is mechanical. A geared butterfly valve is provided to control an accurate flow rate.

 

Flow measurement

A flow digital display is used. In the case of an underground storage tank, a measuring tank with calibrated weir is available as an option. The flow rate is controlled by a geared butterfly valve.

 

Model and Accessories

All accessories and models have side seals to ensure no water seepage or leakage through the sides of the models. A wide variety of models and accessories are available as option.

  • Flow measurement

  • Hydraulic jump

  • Analysis of model structures

  • Gauging structures

  • Velocity profile

  • Continuity and energy equations

  • Similarity laws

  • Roughened bed characteristics

  • Surge propagation

  • Wave generation and absorption

  • Channel size
: 600 mm wide, 700 mm high   
  • Channel length
: 18 m (12 m length can be supplied on request)   
  • Total length
:  Additional length 34 m for head and storage tanks.   
  • Tilting adjustment
: -0.5 to +2%   
  • Side walls
: Tempered glass   
  • Channel bed
:  Stainless steel   
  • Water storage tank
: Underground tank to be provide by user.   
  • Sluice gate
:  Stainless steel, rack and pinion type, built in at downstream end of the channel   
  • Pump
:  1   
  • Flow measurement
:  Water meter with stop watch.   
  • Instrument trolley
:  Manual operation   
  • Power supply
: 380 V, 3 Ph, 50 Hz Other power supply is available on request.   
  • Shipping Dimensions: One 40 ft. container (without storage tank)
  • HF560S                                

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HF560-001A
Motorized instrument trolley instead of manually operated trolley
  • HF560-002
Above ground storage tank, 12 m3
  • HF560-017
Flow calibration tank consisting of two sections where water is discharged into the first section and flows through stilling partition before discharging via calibrated weir into underground tank.
  • HF560-019
Stainless steel vernier hook and point gauge 0-600 mm with 0.05 mm reading or 1 mm graduation
  • HF560-020
Basic weir plate with stainless steel 90˚V notch and rectangular notch weir attachment
  • HF560-022
Sharp crested weir
  • HF560-023
Broad crested weir, sharp edges
  • HF560-023A
Round edge attachment for HF560-023
  • HF560-024
Crump weir
  • HF560-025
Trapezoidal weir
  • HF560-030
Ogee weir consisting of base profile unit with both upstream and downstream pressure tappings and manometer board
  • HF560-031
Dam spillway consisting of base profile unit with different interchangeable downstream sections:
 - Toe, ski jump, piers and pegs, gravel box, or stop logs.
  • HF560-032
USBR type 2,3 or 4 energy dissipater.
  • HF560-033
Syphon spillway made from clear acrylic and PVC.
  • HF560-034
Bridge pier, round or square edge
  • HF560-035
Culvert fittings, round or square, horizontal or drop inlet with or without entrance flare
 Tube is made from clear acrylic
  • HF560-036
Vibration pile
  • HF560-040
Venturi flume made from clear acrylic with stainless steel attachment.
  • HF560-041
Venturi flume made from clear acrylic with stainless steel attachment.
  • HF560-042
Submerged orifice made from stainless steel on plastics.
  • HF560-050
Sluice gate, rack and pinion drive with stainless steel attachment
  • HF560-052
Radial gate, rack and pinion drive with stainless steel attachment.
  • HF560-060
Pitot tube with manometer board for measurement of flow velocity and various channel sections.
  • HF560-061
Current meter
  • HF560-065
Lift and drag balance and models, large and small cylinders and aerofoil section.
  • HF560-070
Roughened bed, gravel, sand, or corrugated
  • HF560-075R
Sediment transport study system with sediment recirculating system
 In this case, pump will be cover with ceramic for corrosion prevention.
  • HF560-080
Wave generator with variable speed geared motor, maximum stroke 30 cm
  • HF560-080F
Full randomly wave generator
 This include HF560-082 and HF560-080M.
  • HF560-080M
Wave measuring system
  • HF560-082
Absorbing beach, plain, roughened, or permeable.
  • HF560-085
End tank, stainless steel, at downstream end of flume.
  • Other accessories and models can be supplied on request.
  • Other optional equipment, please contact manufacturer ([email protected])
  • HF560S                        
: Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
SIMILAR PRODUCTS

HF 530 TILTING FLOW CHANNEL, 300 mm wide

HF 530 TILTING FLOW CHANNEL, 300 mm wide

Enquiry

Download

The channel is designed for studying the hydraulic flow phenomena. It is a service unit to be used with optional accessories and models below. Instruction manual is also included.

 

Under Frame

The channel bed rests on twin beam under frame which ensures static loading deflections are kept to a minimum. Each section is shipped with glass side walls. This simplifies site installation as there is only one joint and is easier to ensure alignment of the channel. The beams are supported by a fulcrum at one end and an adjustable height support at the other end.

 

Slope Adjustment

The adjustable height support uses twin screws. Each screw is driven by a worm and wheel gear box with a common motor. A slope scale is provided at one end of the flume.

 

Channel Bed

The channel bed is made of stainless steel with screw holes of equal distance along the channel length to hold accessories or models to the channel bed. These holes can also be used for pressure tapping to measure pressure loss along the channel length.

 

Side Walls

For safety reasons, the side walls are made of tempered glass or clear acrylic. The walls are supported at interval by brackets with screw adjustment to ensure that the channel wall is straight and vertical.

 

Instrument Carriage

Top rails made of stainless steel tubes are attached to the top angle on each wall of the channel. Screws supporting the rails can be adjusted to ensure uniform height and in a straight line. A scale graduated in mm. is attached along the full length of one top angle of the walls. The instrument carriage is manually operated.

 

Head Tank

The head tank is made of stainless steel and bottom slope to ensure smooth flow into the channel. Perforated sheets are also provided in the head tank to further smoothen the flow.

 

Storage Tank

The storage tank has adequate water to fill the full channel. Fiber glass storage tank(s) is provided at downstream end of the channel. Capacity of tank varies according to channel length.

 

Model Installation

A mobile ladder is used. In the case of small fiber glass tanks (optional) are used, the top covers of the tanks (optional) are used as a walkway and model installation.

 

Circulating Pump

The pump seal is mechanical. A geared butterfly valves is provided for accurate flow control.

 

Flow measurement

A flow digital display is used for easy observation on flow adjustment. A water meter is available as an option and may be used as a reference for flow indicator setting later.

 

Model and Accessories

All accessories and models have side seals to ensure no water seepage or leakage through the sides of the models. A wide variety of models and accessories are available as an option.

  • Flow measurement

  • Hydraulic jump

  • Analysis of model structures

  • Gauging structures

  • Velocity profile

  • Continuity and energy equations

  • Similarity laws

  • Roughened bed characteristics

  • Surge propagation

  • Wave generation and absorption.

  • Flume dimensions
: 300 mm wide, 450 mm high   
  • Flume length
: 12.5 m (5, 7.5, 10 m, or other length can be supplied on request.)   
  • Tilting adjustment
: -1% to +3%.   
  • Side walls

: 6 mm tempered glass.

   
  • Channel bed
: Stainless steel   
  • Water storage tank
:  Fiber glass, Approx. 2 x 1800 L (for 5,7.5 m, approx. 1 x 2000 L is supplied).   
  • Head tank
:  Stainless steel   
  • Sluice gate
:  Stainless steel, rack and pinion type, built in at downstream end of the channel   
  • Circulating Pump
: 5.5 kW with a maximum flow rate approximately 1800 lpm.   
  • Flow measurement
:  Flow digital display.   
  • Instrument carriage
:   Manual operation.   
  • Power supply
: 380 V, 3 Ph, 50 Hz. Other power supply is available on request.   
  • Shipping Dimensions: One 40 ft. container (without storage tank)
  • HF530S

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HF530-001A
Motorized instrument trolley instead of manually operated trolley
  • HF530-019
Stainless steel hook and point gauge 450 mm with 0.05 mm reading graduation.
  • HF530-019A
Stainless steel hook and point gauge 450 mm x 1.0 mm scale.
  • HF 530-BWB
Basic weir base for HF 530-020 , HF 530-021 and HF 530-025.
  • HF530-020
60˚V notch weir.
  • HF530-021
Rectangular notch weir.
  • HF530-022
Sharp crested weir
  • HF530-023
Broad crested weir, sharp edges
  • HF530-023A
Round edge attachment for HF530-023
  • HF530-024
Crump weir
  • HF530-025
Trapezoidal weir
  • HF530-030
Ogee weir consisting of base profile unit with both upstream and downstream pressure tappings and manometer board
  • HF530-031

Dam spillway consisting of base profile unit with different interchangeable downstream sections:

- Toe, ski jump, piers and pegs, gravel box, or stop logs

  • HF530-032
USBR type 2,3 or 4 energy dissipater
  • HF530-033
Syphon spillway made from clear acrylic and PVC
  • HF530-034
Bridge pier, round or square edge
  • HF530-035

Culvert fittings, round or square , horizontal or drop inlet with or without entrance flare

Tube is made from clear acrylic

  • HF530-036
Vibration pile
  • HF530-040
Venturi flume made from clear acrylic with stainless steel attachment.
  • HF530-041
Parshall flume made from clear acrylic with stainless steel attachment.
  • HF530-042
Submerged orifice made from stainless steel on plastics.
  • HF530-043
Trapezoidal flume made from clear acrylic.
  • HF530-050
Sluice gate, rack and pinion drive with stainless steel attachment
  • HF530-052
Radial gate, rack and pinion drive with stainless steel attachment
  • HF530-060
Pitot tube with manometer board for measurement of flow velocity and various channel sections
  • HF530-061
Current meter : digital or analog indicator, low speed probe from 5 to 150 cm/s or high speed probe 60-300 cm/s
  • HF530-065
Lift and drag balance and models, large and small cylinders and aerofoil section
  • HF530-070
Roughened bed, gravel, sand, or corrugated, 2.4 m
  • HF530-071
False floor section.
  • HF530-075
Sediment transport study system.
  • HF530-080
Wave generator with variable speed geared motor.
  • HF530-081
Wave measuring system.
  • HF530-082
Absorbing beach, plain, roughened, or permeable
  • HF530-085
End tank, stainless steel, at downstream end of flume
  • HF530-090          
Checker plate walkway along one side of the flume
  • Pressure tapping points with manometer board.
  • Other accessories and models can be supplied on request.
  • HF530S                        
: Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
SIMILAR PRODUCTS

HF 515A TILTING FLOW CHANNEL, 150 mm wide, Adjustable bed

HF 515A TILTING FLOW CHANNEL, 150 mm wide, Adjustable bed

Enquiry

Video

Download

The settlement of river water sediments over a long period of time results is a shallow river bed. Occasional dredging may be required to deepen the river bed for navigation purpose. The adjustable bed flow channel allows a study of flow under the simulated shallow and deepened river bed.

This is a self contained open channel designed for studying flow phenomena with change in bed slope. It is a service unit to be used with optional accessories and models below.

The channel is of rectangular cross section supported by rectangular steel frame. Side walls are transparent to allow full observation and are supported by adjustable steel brackets to ensure accurate wall alignment.  Tilting can be adjusted by a manual screw jack. The middle section of the bed can be adjusted manually upward or downward by a screw. A head tank with a stilling baffle provides a smooth flow and water is returned to the storage tank via an end tank. Models are attached to the top edges or bed of the flume by screws. Screw holes at the bed can also be used for pressure tapping to measure pressure loss along the channel length.

Instruction manual is also included.

  • Open channel flow

  • Flow measurement

  • Hydraulic jump

  • Continuity and energy equations

  • Discharge under sluice gate

  • Channel size
:  150 mm wide, 350 mm high   
  • Channel length
:  5 m (Extended length can be supplied on request.)   
  • Tilting adjustment
:  -1% to +3%   
  • Side walls
: Clear acrylic or tempered glass, with clear vertical scale   
  • Channel bed
:  Stainless steel   
  • Bed adjustment
: Upward and downward   
  • Water storage tank
:  1   
  • Head tank
:  Stainless steel   
  • Pump      
:  1   
  • End tank
:  Stainless steel   
  • Sluice gate
:  Stainless steel, rack and pinion type, built in at downstream end of the channel   
  • Flow measurement
:  Water meter with stop watch.   
  • Power supply

:  220 V, 1 Ph, 50 Hz. Other power supply is available on request.

   
  • Net (unassembled) Shipping Dimensions WxLxH: 100 x 700 x 160 cm
  • Net Weight:  Approx. 620 kg
  • HF515AS                                    

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HF515-019
Stainless steel vernier hook and point gauge 300 mm x 0.05 mm reading
  • HF515-019A
Stainless steel hook and point gauge 300 mm x 0.5 mm scale
  • HF515-020
Basic weir plate with stainless steel 60˚ V notch and rectangular notch weir attachment
  • HF515-022
Sharp crested weir
  • HF515-023
Broad crested weir, sharp edges
  • HF515-023A
Round edge attachment for HF515-023
  • HF515-024
Crump weir
  • HF510-025
Trapezoidal weir
  • HF515-030
Ogee weir consisting of base profile unit with both upstream and downstream pressure tappings and manometer board
  • HF515-031

Dam spillway consisting of base profile unit with different interchangeable downstream sections:

-  Toe, ski jump, piers and pegs, gravel box, or stop logs

  • HF515-033
Syphon spillway made from clear acrylic and PVC
  • HF515-034
Bridge pier, round or square
  • HF515-035
Culvert fittings: round or square , horizontal or drop inlet with or without entrance flare
  • HF515-036
Vibration pile
  • HF515-040
Venturi flume made from clear acrylic with stainless steel attachment.
  • HF515-050
Sluice gate, rack and pinion drive with stainless steel attachment
  • HF515-051
Sluice gate, sliding type with stainless steel attachment
  • HF515-052
Radial gate, rack and pinion drive, with stainless steel attachment
  • HF515-060
Pitot tube with manometer board for measurement of flow velocity at various channel actions
  • HF515-061
Current meter
  • HF515-070
Roughened bed, gravel, sand, or corrugated, 1.2 m
  • HF515-080
Wave generator with variable speed geared motor
  • HF515-081
Motorized tilting
  • HF515-082
Absorbing beach, plain, roughened, or permeable, 1.2 m
  • HP010
Flow digital display
  • Other accessories and models can be supplied on request.
  • Other optional equipment, please contact manufacturer ([email protected])
  • HF515AS                        
: Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
SIMILAR PRODUCTS

HF 515 TILTING FLOW CHANNEL, 150 mm wide

HF 515 TILTING FLOW CHANNEL, 150 mm wide

Enquiry

Video

Download

This is a self contained open channel designed for studying a flow phenomena. It is a service unit to be used with optional accessories and models below.

The channel is of rectangular cross section supported by rectangular steel frame. Side walls are transparent to allow full observation and are supported by adjustable steel brackets to ensure accurate wall alignment.  Tilting can be adjusted by a manual screw jack. A head tank with a stilling baffle provides a smooth flow and water is returned to the storage tank via an end tank. Models are attached to the top edges or bed of the flume by screws. Screw holes at the bed can also be used for pressure tapping to measure pressure loss along the channel length.

Instruction manual is also included.

  • Open channel flow

  • Flow measurement

  • Hydraulic jump

  • Continuity and energy equations

  • Discharge under sluice gate

  • Channel size
:  150 mm wide, 350 mm high
  • Channel length
:  5 m (Extended length can be supplied on request.)
  • Tilting adjustment
:  -1% to +3%
  • Side walls
: Clear acrylic or tempered glass, with clear vertical scale
  • Channel bed
:  Stainless steel
  • Water storage tank
:  1
  • Head tank
:  Stainless steel
  • Pump
:  1
  • End tank
:  Stainless steel
  • Sluice gate
:  Stainless steel, rack and pinion type, built in at downstream end of the channel
  • Flow measurement
:  Water meter with stop watch.
  • Power supply
:  220 V, 1 Ph, 50 Hz. Other power supply is available on request.
  • Net (unassembled) Shipping Dimensions WxLxH: 100 x 700 x 160 cm
  • Net Weight:  Approx. 620 kg
  • HF515S                                    

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HF515-019
Stainless steel vernier hook and point gauge 300 mm x 0.05 mm reading
  • HF515-019A
Stainless steel hook and point gauge 300 mm x 0.5 mm scale
  • HF515-020
Basic weir plate with stainless steel 60˚ V notch and rectangular notch weir attachment
  • HF515-022
Sharp crested weir
  • HF515-023
Broad crested weir, sharp edges
  • HF515-023A
Round edge attachment for HF515-023
  • HF515-024
Crump weir
  • HF510-025
Trapezoidal weir
  • HF515-030
Ogee weir consisting of base profile unit with both upstream and downstream pressure tappings and manometer board
  • HF515-031

Dam spillway consisting of base profile unit with different interchangeable downstream sections:

-  Toe, ski jump, piers and pegs, gravel box, or stop logs

  • HF515-033
Syphon spillway made from clear acrylic and PVC
  • HF515-034
Bridge pier, round or square
  • HF515-035
Culvert fittings: round or square , horizontal or drop inlet with or without entrance flare
  • HF515-036
Vibration pile
  • HF515-040
Venturi flume made from clear acrylic with stainless steel attachment.
  • HF515-050
Sluice gate, rack and pinion drive with stainless steel attachment
  • HF515-051
Sluice gate, sliding type with stainless steel attachment
  • HF515-052
Radial gate, rack and pinion drive, with stainless steel attachment
  • HF515-060
Pitot tube with manometer board for measurement of flow velocity at various channel actions
  • HF515-061
Current meter
  • HF515-070
Roughened bed, gravel, sand, or corrugated, 1.2 m
  • HF515-080
Wave generator with variable speed geared motor
  • HF515-081
Motorized tilting
  • HF515-082
Absorbing beach, plain, roughened, or permeable, 1.2 m
  • HP010
Flow digital display
  • Other accessories and models can be supplied on request.
  • Other optional equipment, please contact manufacturer ([email protected])
  • HF515S                        
: Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
SIMILAR PRODUCTS

HF 510A TILTING FLOW CHANNEL,100 mm. wide, Adjustable bed

HF 510A TILTING FLOW CHANNEL,100 mm. wide, Adjustable bed

Enquiry

Video

Download

This is a self-contained open channel designed for studying flow phenomena. It is a service unit to be used with optional accessories and models below.

The channel is of rectangular cross section supported by rectangular steel frame. Side walls are transparent to allow full visual observation and are supported by adjustable steel brac

The settlement of river water sediments over a long period of time results is a shallow river bed. Occasional dredging may                  be required to deepen the river bed for navigation purpose. The adjustable bed flow channel allows a study of flow under the simulated shallow and deepened river bed.

kets to ensure accurate wall alignment.  Tilting can be adjusted by a manual screw jack. A head tank with a stilling baffle provides a smooth flow and water is returned to the storage tank via an end tank. Models are attached to the top edges or bed of the flume by screws. Screw holes at the bed can also be used for pressure tapping to measure pressure loss along the channel length.

Instruction manual is also included.

This is a self-contained open channel designed for studying flow phenomena with a change in bed slope. It is a service unit to be used with optional accessories and models below.

The channel is of rectangular cross section supported by a rectangular steel frame. Side walls are transparent to allow full visual observation and are supported by adjustable steel brackets to ensure accurate wall alignment.  Tilting can be adjusted by a manual screw jack. The middle section of the bed can be adjusted manually upward or downward by a screw. A head tank with a stilling baffle provides smooth flow and water is returned to the storage tank via an end tank. Models are attached to the top edges or bed of the flume by screws. Screw holes at the bed can also be used for pressure tapping to measure pressure loss along the channel length.

Instruction manual is also included.

  • Open channel flow

  • Flow measurement

  • Hydraulic jump

  • Continuity and energy equations

  • Discharge under sluice gate

  • Critical depth and its influences on upstream water levels

  • Channel size
:  100 mm wide, 300 mm high   
  • Channel length
:  4 m (Extended length can be supplied on request.)   
  • Tilting adjustment
:  -2% to +5%   
  • Side walls
:  Clear acrylic tempered glass with clear vertical scale   
  • Channel bed
:  Stainless steel   
  • Bed adjustment
:  Upward or downward   
  • Water storage tank
:  1   
  • Pump
:  1   
  • Head tank
:  Stainless steel   
  • End tank
:  Stainless steel   
  • Sluice gate
:  Stainless steel, rack and pinion type, built in at downstream end of the channel   
  • Flow measurement
:  Water meter with stop watch.   
  • Power supply

:  220 V, 1 Ph, 50 Hz. Other power supply is available on request.

   
  • Net (unassembled) Shipping Dimensions WxLxH: 80 x 500 x 150 cm
  • Net Weight:  Approx. 440 kg
  • HF510AS                                         

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HF510-019
Stainless steel vernier hook and point gauge 300 mm x 0.05 mm reading
  • HF510-019A
Stainless steel hook and point gauge 300 mm x 0.5 mm scale
  • HF510-020
Basic weir plate with stainless steel 60˚ V notch and rectangular notch weir attachment
  • HF510-022
Sharp crested weir
  • HF510-023
Broad crested weir, sharp edges
  • HF510-023A
Round edge attachment for HF510-023
  • HF510-024
Crump weir
  • HF510-025
Trapezoidal weir
  • HF510-030
Ogee weir consisting of base profile unit with both upstream and downstream pressure tappings and manometer board
  • HF510-031

Dam spillway consisting of base profile unit with different interchangeable downstream sections:

-  Toe, ski jump, piers and pegs, gravel box, or stop logs

  • HF510-033
Syphon spillway made from clear acrylic and PVC
  • HF510-034
Bridge pier, round or square
  • HF510-035
Culvert fittings: round or square , horizontal or drop inlet with or without entrance flare
  • HF510-036
Vibration pile
  • HF510-040
Venturi flume made from clear acrylic with stainless steel attachment.
  • HF510-050
Sluice gate, rack and pinion drive with stainless steel attachment
  • HF510-051
Sluice gate, sliding type with stainless steel attachment
  • HF510-052
Radial gate, rack and pinion drive, with stainless steel attachment
  • HF510-060
Pitot tube with manometer board for measurement of flow velocity at various channel actions
  • HF510-061
Current meter
  • HF510-070
Roughened bed, gravel, sand, or corrugated
  • HF510-080
Wave generator with variable speed geared motor
  • HF510-082
Absorbing beach, plain, roughened, or permeable, 1.2 m
  • HP010
Flow digital display
  • Other accessories and models can be supplied on request.
  • Other optional equipment, please contact manufacturer ([email protected])
  • HF510AS                        
: Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
SIMILAR PRODUCTS

HF 510 TILTING FLOW CHANNEL,100 mm. wide

HF 510 TILTING FLOW CHANNEL,100 mm. wide

Enquiry

Video

Download

This is a self-contained open channel designed for studying flow phenomena. It is a service unit to be used with optional accessories and models below.

The channel is of rectangular cross section supported by rectangular steel frame. Side walls are transparent to allow full visual observation and are supported by adjustable steel brackets to ensure accurate wall alignment.  Tilting can be adjusted by a manual screw jack. A head tank with a stilling baffle provides a smooth flow and water is returned to the storage tank via an end tank. Models are attached to the top edges or bed of the flume by screws. Screw holes at the bed can also be used for pressure tapping to measure pressure loss along the channel length.

Instruction manual is also included.

  • Open channel flow

  • Flow measurement

  • Hydraulic jump

  • Continuity and energy equations

  • Discharge under sluice gate

  • Critical depth and its influences on upstream water levels

  • Channel size

:  100 mm wide, 300 mm high

   
  • Channel length
:  4 m (Extended length can be supplied on request.)   
  • Tilting adjustment
:  -2% to +5%   
  • Side walls

:  Clear acrylic tempered glass with clear vertical scale

   
  • Channel bed
:  Stainless steel   
  • Head tank
:  Stainless steel   
  • End tank
:  Stainless steel   
  • Sluice gate
:  Stainless steel, rack and pinion type, built in at downstream end of the channel   
  • Pump
:  1   
  • Flow measurement
:  Water meter and stop watch   
  • Power supply

:  220V 1 Ph 50 Hz. Other power supply is available on request.

   
     
  • Net (unassembled) Shipping Dimensions WxLxH: 70 x 520 x 160 cm
  • Net Weight:  Approx. 390 kg
  • HF510S                                         

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HF510-019
Stainless steel vernier hook and point gauge 300 mm x 0.05 mm reading
  • HF510-019A
Stainless steel hook and point gauge 300 mm x 0.5 mm scale
  • HF510-020
Basic weir plate with stainless steel 60˚ V notch and rectangular notch weir attachment
  • HF510-022
Sharp crested weir
  • HF510-023
Broad crested weir, sharp edges
  • HF510-023A
Round edge attachment for HF510-023
  • HF510-024
Crump weir
  • HF510-025
Trapezoidal weir
  • HF510-030
Ogee weir consisting of base profile unit with both upstream and downstream pressure tappings and manometer board
  • HF510-031

Dam spillway consisting of base profile unit with different interchangeable downstream sections:

-  Toe, ski jump, piers and pegs, gravel box, or stop logs

  • HF510-033
Syphon spillway made from clear acrylic and PVC
  • HF510-034
Bridge pier, round or square
  • HF510-035
Culvert fittings: round or square , horizontal or drop inlet with or without entrance flare
  • HF510-036
Vibration pile
  • HF510-040
Venturi flume made from clear acrylic with stainless steel attachment.
  • HF510-050
Sluice gate, rack and pinion drive with stainless steel attachment
  • HF510-051
Sluice gate, sliding type with stainless steel attachment
  • HF510-052
Radial gate, rack and pinion drive, with stainless steel attachment
  • HF510-060
Pitot tube with manometer board for measurement of flow velocity at various channel actions
  • HF510-061
Current meter
  • HF510-070
Roughened bed, gravel, sand, or corrugated
  • HF510-080
Wave generator with variable speed geared motor
  • HF510-082
Absorbing beach, plain, roughened, or permeable, 1.2 m
  • HP010
Flow digital display
  • Other accessories and models can be supplied on request.
  • Other optional equipment, please contact manufacturer ([email protected])
  • HF510S                        
: Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
SIMILAR PRODUCTS

HF 509 OPEN CHANNEL AND CLOSED CHANNEL FLOW

HF 509 OPEN CHANNEL AND CLOSED CHANNEL FLOW

Enquiry

Video

Download

This is a floor standing open channel which can be quickly converted into a closed channel for studying both open and closed channel flow. It is to be used with HB100 Hydraulics Bench (separately supplied)

The channel has transparent side walls with tanks at both ends for supplying water to and receiving water from the channel. Each tank has a flow control valve to control flow and water level in the channel. The inlet tank has a stilling arrangement. A removable lid is placed on top of the open channel to convert it to a closed channel. The mid section of the channel bed is adjustable for demonstration of Bernoulli theorem in closed conduit flow.

Accessories and measuring instruments are provided for the flow study.

Instruction manual is also included.

  • Open Channel Flow               

          -  Flow over sharp crested, broad crested and ogee weirs

          -  Flow under sluice gate

          -  Subcritical, critical and super critical flow

          -  Energy dissipation

          -  Hydraulic jump

  • Closed Channel Flow

          -  Bernoulli and continuity equations

          -  Measurement of static pressure and total pressure

          -  Calculation of flow velocity         

  • Channel size
:  750 mm wide, 150 mm high   
  • Channel length
:  1.2 m   
  • Bed adjustment
:  Up to 75 mm upward   
  • Measuring instruments
    
- Manometer:  1 set.   
- Pitot tubes:  3   
  • Accessories
    
- Sluice gates:  2   
- Weirs:  3   
- Bridge pier:  1   
- Removable lid for closed channel conversion :  1   
- Connecting hose :  1   
  • Net (unassembled) Shipping Dimensions WxLxH: 78 x 163 x 173 cm
  • Net Weight:  Approx. 66.5 kg
  • HF509S                                

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HF509-001
Water supply system
 :  0.37 kW pump with storage tank, water meter and hose
 :  Power supply; 220V, 1 Ph, 50 Hz. Other power supply is available on request.
  • HB100N or HB100
Hydraulic Bench, Neo or Hydraulics Bench
  • Other accessories and models can be supplied on request.
  • Other optional equipment, please contact manufacturer ([email protected])
  • HF509S                        
: Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
SIMILAR PRODUCTS

HF 508 TILTING FLOW CHANNEL, 75 mm. wide

HF 508 TILTING FLOW CHANNEL, 75 mm. wide

Enquiry

Video

Download

This is a bench top, self contained open channel designed for studying flow phenomena. It is a service unit to be used with optional accessories and models below.

The channel is of rectangular cross section supported by a steel frame. Side walls are transparent to allow full visual observation. Tilting can be adjusted by a manual screw jack. A stainless-steel head tank with a stilling baffle provides a smooth flow and water is returned to the storage tank.

Instruction manual is also included.

  • Flow measurement
  • Hydraulic jump

  • Continuity and energy equations

  • Discharge under sluice gate

  • Channel size
:  75 mm wide, 250 mm high
  • Channel length
:  2.5 m (Extended length can be supplied on request.)
  • Tilting adjustment
:  -2% to + 5%
  • Side walls
:  Clear acrylic with clear vertical scale
  • Channel bed
:  Stainless steel
  • Pump
:  1
  • Water storage tank
:  1
  • Flow measurement
:  Water meter with stop watch.
  • Power supply
:  220 V, 1 Ph, 50 Hz. Other power supply is available on request.
  • Net (unassembled) Shipping Dimensions WxLxH: 60 x 340 x 90 cm
  • Net Weight:  Approx. 150 kg
  • HF508S            

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HF507-019
Stainless steel vernier hook and point gauge 300 mm with 0.05 mm reading
  • HF507-019A
Stainless steel hook and point gauge 300 mm x 0.5 mm scale
  • HF507-020
Basic weir plate with stainless steel 60˚V notch and rectangular notch weir attachment
  • HF507-022
Sharp crested weir
  • HF507-023
Broad crested weir, sharp edges
  • HF507-023A
Round edge attachment for HF507-023
  • HF507-024
Crump weir
  • HF507-025
Trapezoidal weir
  • HF507-030
Ogee weir consisting of base profile unit with both upstream and downstream pressure tappings and manometer board.
  • HF507-031            

Dam spillway consisting of base profile unit with different interchangeable downstream sections:

-  Toe, ski jump, piers and pegs, gravel box, or stop logs

  • HF507-033
Syphon spillway made from clear acrylic and PVC
  • HF507-034
Bridge pier, round or square
  • HF507-035
Culvert fittings, round or square edge
  • HF507-040
Venturi flume made from clear acrylic with stainless steel attachment.
  • HF507-051
Sluice gate, sliding type with stainless steel attachment
  • HF507-052
Radial gate, rack and pinion drive, with stainless steel attachment.
  • HF507-060
Pitot tube with manometer board for measurement of flow velocity at various channel sections.
  • HF507-061
Current meter
  • HF507-070
Roughened bed, gravel, sand, or corrugated
  • HF507-080
Wave generator with variable speed geared motor
  • HP010
Flow digital display
  • Other accessories and models can be supplied on request.

  • Other optional equipment, please contact manufacturer ([email protected])

  • HF508S                        
: Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
SIMILAR PRODUCTS