HB 019 ORIFICE AND JET FLOW

HB 019 ORIFICE AND JET FLOW

Enquiry

Download

This equipment allows determination of coefficient of velocity and coefficient of discharge under various constant heads for two different orifice diameters. Comparison of jet trajectory with that by theory of mechanics can also be made. The equipment is to be used with Hydraulics Bench i.e. HB100 or HB100N (separately supplied) for a water supply and flow measurement.

The equipment consists of a removable clear acrylic cylinder with sharp edge orifice installed at the lower inside wall of the cylinder. An adjustable overflow allows various constant heads for the test and trajectory of the jet is indicated by probes on the jet path. Heights of the probes are indicated by scales. The apparatus rests on adjustable footings and a level gauge is provided

Instruction manual is also included.

  • Comparison of the actual and theoretical outlet velocity

  • Calculation of discharge coefficient

  • Determination of the contraction and velocity coefficients

  • Determination of discharge characteristics (jet trajectory) for an orifice mounted in the side of a vertical tank and comparison with simple theory

  • Orifice diameter
:  2 different sizes
  • Trajectory probes
:  8, stainless steel
  • Acrylic
:  1
  • Measuring cup
:  1 L
  • Net (unassembled) Shipping Dimensions WxLxH:  36 x 68 x 70 cm
  • Net Weight:  Approx. 10 kg
  • HB019S

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HB019-001    
Bottom discharge with traverse mechanism 0.01 mm division and wire for measurement of jet diameter, pitot tube to measure jet velocity and three orifices.
HB019S  

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

SIMILAR PRODUCTS

HB 018 BENDS AND FITTINGS FRICTION

HB 018 BENDS AND FITTINGS FRICTION

Enquiry

Download

The equipment measures pressure drops at various flow rates when water flow through different pipe bends, and fittings. It is to be used with Hydraulics Bench i.e. HB100 or HB100N (separately supplied) for a water supply and flow measurement.

All bends and fittings are connected in series with pressure tappings on both sides of each device. A water manometer with a vent valve and a hand air pump is connected to these tappings. A valve at the outlet is used to control outlet pressure.

Instruction manual is also included.

  • Determination of Pressure Drop across various pipes and fittings at differing flow rates.

  • Estimation of Loss Coefficient (K) on various pipes, pipe fittings and valve settings

  • Pipe diameter (nominal)
:  20 mm
  •   Enlarged pipe diameter (nominal)
:  35 mm
  • Bends
:  90º Miter bend :  90º small radius bend :  90º large radius bend
  • Fittings
:  90º Elbow :  45º elbow :  Sudden expansion :  Sudden contraction
  • Water manometer
:  8 tubes x 450 mm
  • Net (unassembled) Shipping Dimensions WxLxH: 36 x 55 x 80 cm
  • Net Weight:  Approx. 13 kg
  • HB018S

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HB018-001      

A gate valve with pressure gauges for measuring pressure loss across the valve

  • HF011-035

Variable area flow meter, up to 35 LPM for flow rate indication.

HB018S  

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

SIMILAR PRODUCTS

HB 017 PIPE FRICTION

HB 017 PIPE FRICTION

Enquiry

Video

Download

This equipment measures pressure drop when water flows through a vertical pipe at various flow rates both laminar and turbulent. It is to be used with Hydraulics Bench i.e. HB100 or HB100N (separately supplied) for a water supply and flow measurement.

It consists of adjustable constant head water source of removable clear acrylic cylinder for laminar flow. Turbulent flow may be achieved by directly connecting the pipe to the Hydraulics Bench water supply. A water manometer with a vent valve, a hand air pump and a differential pressure gauge are provided for measurement of pressure drop. A valve at the outlet is used to control outlet pressure.

Instruction manual is also included.

  • Investigations of laminar and turbulent flows

  • Demonstration and measurement in a change of the laws of resistance (friction factor) from laminar to turbulent flow

  • Acrylic cylinder
:  1   
  • Venturi tube
:  450 mm   
  • Differential pressure gauge
:  1   
  • Test pipe
: Stainless steel   
  • Test section length
: Over 500 mm   
  • Measuring cup
: 1   
  • Net (unassembled) Shipping Dimensions WxLxH: 36 x 36 x 115 cm
  • Net Weight:  Approx. 10 kg
  • HB017S

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HB017-001A
Horizontal test pipe instead standard vertical pipe
  • HF033A
Differential pressure digital display, 0-500 cm water instead of differential pressure gauge
  • HF033C

Portable differential pressure meter, 0-2100 mbar, 0.2% accuracy instead of differential pressure gauge

  • MW102M-450A              
U-tube mercury manometer instead of differential pressure gauge
 

- Range : 450 mm x 1 mm graduation

Note: Due to transport laws, mercury cannot be supplied. Buyer must source it locally.
Approximately 25 mL or 350g is required. Filling kit is provided.

  • HB017S

Learning Software

to support both online/offline training with data  calculation and analysis by manual data entry from analog measuring instruments.

 

SIMILAR PRODUCTS

HB 016P PITOT TUBE APPARATUS

HB 016P PITOT TUBE APPARATUS

Enquiry

Video

Download

This apparatus is for a study of velocity distribution across pipe section for a water flow in pipe, and for measurement of flow velocity. It is to be used with Hydraulics Bench i.e. HB 100 or HB100N (separately supplied) for a water supply and flow measurement.

The apparatus consists of a total head tube and a static head tube for the Pitot, clear acrylic pipe, inlet and outlet, and an inclined manometer. The total head tube can be moved up or down vertically with a scale for indication of the tube position. Differential pressure is measured by a multiple inclination manometer.

Instruction manual is also included

  • Accuracy of pitot tube meters

  • Losses and “k” value

  • Calculation of the coefficient of discharge

  • Acrylic tube
    
     - Inside diameter:  34 mm   
  • Total head tube diameter
:  1   
  •  Manometer
    
     - Inclination:  Adjustable slope   
     - Scale :  0-450 mm x 1 mm graduation   
  • Net (unassembled) Shipping Dimensions WxLxH: 36 x 82 x 19 cm
  • Net Weight:  Approx. 2 kg
  • HB016PS

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

HB016PS  

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

SIMILAR PRODUCTS

HB 016 FLOW METERS

HB 016 FLOW METERS

Enquiry

Download

This equipment determines the coefficients of discharge for different flow measuring devices. It is to be used with Hydraulics Bench i.e. HB100 or HB100N (separately supplied) for a water supply and flow measurement.

The equipment consists of a Venturi tube, an orifice plate, and a Pitot tube, made from a clear acrylic, connected in series. Pressure drop across each device is connected to a water manometer bank with a vent valve and a hand air pump.

Instruction manual is also included.

  • Accuracy of different flow meters

  • Losses and k value

  • Calculation of the coefficient of discharge

  • Variable area flow meter    

:  1

   
  • Venturi tube
:  1   
  • Orifice plate
:  1   
  • Pitot tube
:  1   
  • Water manometer
: 8 tubes   
  • Net (unassembled) Shipping Dimensions WxLxH: 36 x 72 x 78 cm
  • Net Weight:  Approx. 16 kg
  • HB016S
Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
  • HB013A
ISA nozzle on 29 mm diameter tube instead of orifice plate or Pitot tube
HB016S  

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

SIMILAR PRODUCTS

HB 015 BERNOULLI’S THEOREM APPARATUS

HB 015 BERNOULLI’S THEOREM APPARATUS

Enquiry

Download

Bernoulli’s theorem is applied on flow through a clear acrylic Venturi tube. The apparatus is to be used with Hydraulics Bench i.e. HB100 or HB100N (separately supplied) for a water supply and flow measurement.

Static pressures at various points along the wall of a transparent Venturi tube are directly measured on a manometer equipped with a vent valve. A movable stainless steel total head probe is also provided. Flow through the Venturi tube is controlled by a valve at the outlet. As a primary flow measuring device, coefficient of discharge for the Venturi tube can also be determined.

Instruction manual is also included.

  • Application of the Bernoulli equation

  • Measurement of the meter coefficient of discharge at various flow rates

  • Comparison of experimental results with theoretical predictions

  • Diameters
:  28 mm inlet with 14 mm throat
  • Water manometer
:  8 tubes
  • Total head probe
:  1
  • Net (unassembled) Shipping Dimensions WxLxH: 36 x 60 x 83 cm
  • Net Weight:  Approx. 6 kg
  • HB015S
Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
  • HF011-035
Variable area flow meter, up to 35 LPM for flow rate indication
HB015S  

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

SIMILAR PRODUCTS

HB 014 METACENTRIC HEIGHT

HB 014 METACENTRIC HEIGHT

Enquiry

Download

This equipment is designed to determine the metacentric height of a floating body and the height variation with the tilt angle. It is to be used with Hydraulics Bench i.e. HB100 or HB100N or a bowl (separately supplied).

The equipment consists of a rectangular pontoon. The center of gravity of the pontoon can be moved sideways by moving horizontal jockey weight.

The angle of tilt of the pontoon is indicated by a plumb-bob on a scale attached. The center of gravity of the pontoon can also be moved vertically by means of adjustable vertical weights on the mast.

Instruction manual is also included.

  • Experiment to illustrate the floatation characteristics

  • Determination of the metacentric height

  • Comparison of different shapes of pontoon (optional)

  • Pontoon   

:  400 mm long x 200 mm wide x 100 mm high

   
  • Horizontal scale
:  1 mm graduation.   
  • Maximum angle of tilt  
:  ± 13º x 0.5º graduation   
  • Vertical sliding weight
:  1   
  • Jockey weight
:  1   
  • Net (unassembled) Shipping Dimensions WxLxH: 22 x 40 x 48 cm
  • Net Weight:  Approx. 3 kg
  • HB014S
Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
  • HB014-001
Different shape of pontoon i.e., hard chine and round bilge
HB014S  

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

SIMILAR PRODUCTS

HB 013 FLOW OVER A NOTCH

HB 013 FLOW OVER A NOTCH

Enquiry

Download

The apparatus is for the study of flow over a notched weir. It is to be used with Hydraulics Bench i.e. HB100 or HB100N (separately supplied) for a water supply and flow measurement.

Two weir plates, a rectangular notch and two V notches, are provided. Characteristics of flow over the notches can be observed and coefficients of discharge can be determined. The plates are attached to the open channel of the Hydraulics Bench. Water is supplied to the channel via a discharge diffuser and passes through a stilling baffle to smooth the flow. A vernier hook and point gauge is provided to measure the height of water level in the channel.

Instruction manual is also included.

  • Investigation of head against discharge\

  • Coefficient of discharge for notches

  • Demonstration of flow over different notch weirs

  • Stainless steel weir plates    
    
     - Type of notch

: Rectangular

   
   : 90o V   
  • Stainless steel vernier hook and point gauge

: range 0-150 mm

   
     
  • Net (unassembled) Shipping Dimensions WxLxH: 36 x 55 x 35 cm
  • Net Weight:  Approx. 6.5 kg
  • HB013S

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

  • HB013-001

Different angle V notch weir i.e., 30 o or 60o

  • HB013-002

Plastics broad crested weir

  • HB013-003

Stainless steel trapezoidal weir

  • HB013-005

Stainless steel linear head/flow weir

HB013S  

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

SIMILAR PRODUCTS

HB 012B HYDROSTATIC PRESSURE, Tilting Jar Quadrant

HB 012B HYDROSTATIC PRESSURE, Tilting Jar Quadrant

Enquiry

Video

Download

This equipment allows the moment caused by a fluid thrust on a wholly or partially filled plane surface to be measured directly.  This surface can be tilted.

A clear acrylic hollow quadrant is hinged with ball bearings onto a fixed arm which coincides with the quadrant center. A lever arm is also hinged on the same axis.  The quadrant can be tilted by changing the lock pin position. At the other end of the lever arm is an adjustable counter weight. 

A depth scale for water and angular scale for quadrant tilting are indicated on the quadrant.  When water is admitted into the quadrant the lever arm will tilt. Sliding weights with hanger are then applied to the arm to balance the quadrant with water.  The weight can be moved linearly on a scale such that the exact turning moment can be determined.

The apparatus rests on adjustable footings and a bull’s eye level is provided.

Instruction manual is also included.

  • Determination of the Centre of Pressure on Vertical Plane and inclined planes

  • Determination of total Resultant Force acting on Vertical Plane and inclined planes

  •  Quadrant Inner radius        
:  100 mm   
     - Outer radius

: 200 mm

   
     - Width:  75 mm   
  • Tilting angle

:  0 to 30 degrees in either direction.

   
  •  Weights

:  1 lot

   
  • Net (unassembled) Shipping Dimensions WxLxH: 15 x 55 x 45 cm
  • Net Weight:  Approx. 4.6 kg
  • HB012BS

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring  instruments.

 

HB012BS  

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

SIMILAR PRODUCTS

HB 012A HYDROSTATIC PRESSURE

HB 012A HYDROSTATIC PRESSURE, Tilting Submerged Quadrant

Enquiry

Download

This equipment allows the moment caused by a fluid thrust on a wholly or partially submerged plane surface to be measured directly. This surface can be tilted.

A PVC quadrant is hinged on a shaft pivoted on knife edges which coincide with the quadrant center. The quadrant position is adjustable relative to a balance arm such that the submerged plane surface can be tilted by changing the lock pin position. A depth scale is indicated on the quadrant. When the quadrant is immersed in water, there are hydrostatic forces.

The balance arm has an adjustable counter balance and weights with a hanger. The quadrant is mounted on top of a clear acrylic tank which allows water to be admitted and drained to required level by a valve. The tank rests on adjustable footings and a bull’s eye level is provided.

Instruction manual is also included.

  • Determination of the Centre of Pressure on vertical plane and inclined planes
  • Determination of total Resultant Force acting on vertical plane and inclined planes
  •  Quadrant Inner radius        
:  100 mm   
     - Outer radius

: 200 mm

   
     - Width:  75 mm   
  • Tilting angle

:  0 to 30 degrees in either direction.

   
  •  Weights

:  1 lot

   
  • Net (unassembled) Shipping Dimensions WxLxH: 36 x 55 x 35 cm
  • Net Weight:  Approx. 6.5 kg
  • HB012AS
Learning Software to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.
 
  • HB012AS  

Learning Software

to support both online/offline training with data calculation and analysis by manual data entry from analog measuring instruments.

SIMILAR PRODUCTS